Geiger g25 in Sweden (english)

Eure Fragen, Hilfestellung zur Kaufentscheidung, Tipps & Tricks zu Drechselmaschinen.

Moderator: Forenteam

dithes
Beiträge: 14
Registriert: 04.11.2020 - 20:02:55
Name: P E

Re: Geiger g25 in Sweden (english)

Beitrag von dithes »

Oglinchen hat geschrieben: 24.05.2021 - 07:30:09
Hi
You did an very nice Job. Place the small Lathe on an concrete base and srew it tightly.
Or Level it with screws and nuts on a first base, and then cast with concrete the final base.
with greets, Oggi
Thanks!

I don´t think I can cast a concrete base, I only rent my workshop. Is there any other option?
Oglinchen
Beiträge: 1030
Registriert: 20.09.2015 - 18:07:34
Name: Uwe Klein
PLZ: 69429
Ort: Waldbrunn

Re: Geiger g25 in Sweden (english)

Beitrag von Oglinchen »

Screw it on a wooden base. 50mm plywood with a rubber between base and Floor.
Deutsch ist einfach:
Umfahren ist das Gegenteil von Umfahren.
dithes
Beiträge: 14
Registriert: 04.11.2020 - 20:02:55
Name: P E

Re: Geiger g25 in Sweden (english)

Beitrag von dithes »

Hi!

I did notice some runout on my geiger today, what is normal spindle runout on this machine?
Mine was at 0.1mm but after some messing around I got it down to 0.05mm.
Does anyone know what the problem could be?

Thanks
finn2012
Beiträge: 24
Registriert: 02.10.2017 - 19:15:06
Ort: Soest

Re: Geiger g25 in Sweden (english)

Beitrag von finn2012 »

Edward,

perhaps you'll find the requested tolerances (second to last column) in the attached table.

Best regards

Uli

Geiger G25 tolerances.jpg
Geiger G25 tolerances.jpg (191.49 KiB) 1531 mal betrachtet
dithes
Beiträge: 14
Registriert: 04.11.2020 - 20:02:55
Name: P E

Re: Geiger g25 in Sweden (english)

Beitrag von dithes »

Thanks!

So nr 3 is the spindle right? Then its normal with 0.05 and 0.1mm?
Benutzeravatar
jockel
MicroMaster
Beiträge: 3492
Registriert: 21.10.2007 - 16:16:47
Name: Joachim Mader
PLZ: 64395
Ort: Brensbach
Kontaktdaten:

Re: Geiger g25 in Sweden (english)

Beitrag von jockel »

No3 is the axial runout tolerance
No2 is the radial runout tolerance
Die Spuren der Vergänglichkeit sind Qualität!
hera
Beiträge: 537
Registriert: 16.02.2016 - 16:17:05
Name: Hermann Rathkamp
PLZ: 29229
Ort: Celle

Re: Geiger g25 in Sweden (english)

Beitrag von hera »

Edward,
let me try to translate the line items shown in the table provided by Uli.

1 bed flatness, straightness a.) longitudinal, b.) across

2 inner chamfer /female taper of the spindle, a.) runout, concentricity, b.) alingnment

3 a.) flange, axial runout, b.) center point runout

4 a.) testcylinder concentricity b.) face plate 300mm runout

5 axis parallel to bed, vertical/horizontal

6 tailstock center/quill sleeve parallel to bed a.) vertical, b.) horizontal

7 alignment of tailstock center point a.)vertical, b.) horizontal

the table shows the acceptable values in the 2nd last column, the actual measurements in the last column.


Spindle radial concentricity values are show at 2a and 4a with 0,03, actual 0,02 / 0,01

rgds
hermann
Das Leben ist zu kurz für schlechten Wein und stumpfes Werkzeug !
dithes
Beiträge: 14
Registriert: 04.11.2020 - 20:02:55
Name: P E

Re: Geiger g25 in Sweden (english)

Beitrag von dithes »

Thanks guys!

Seems like my geiger has a problem then, anyone know what the cause could be?
The bearings are new skf, changed just some month ago.
Antworten

Zurück zu „Drechselmaschinen allgemein“